-dC- error code
Twin Mode partition fault
What does Samsung Range, wall oven or induction cooktop -dC- mean?
The oven partition is missing, incorrectly installed or the partition switch is obstructed. Samsung uses -dC- to identify a door, lid or latch condition on the affected cooking appliance. The code is a diagnostic starting point rather than proof that one specific part has failed. Confirm the complete code, exact model number and region before using repair information or ordering components.
The code identifies the condition detected by the product; it does not always identify the failed component on its own. Confirm the full code and exact model before ordering parts or attempting a reset.
The Samsung Range, wall oven or induction cooktop -dC- error code indicates the oven partition is missing, incorrectly installed or the partition switch is obstructed. Samsung uses -dC- to identify a door, lid or latch condition on the affected cooking appliance. The code is a diagnostic starting point rather than proof that one specific part has failed. Confirm the complete code, exact model number and region before using repair information or ordering components. This guide explains what the code means, the symptoms and likely causes, the checks that are safe to make, and when to stop and arrange an authorised repair.
Symptoms you may notice
- The cooking appliance displays -dC- and may interrupt its cooking or heating operation.
- The selected element or oven function may not heat or may stop early.
- Controls may be restricted until the condition is cleared.
- The code may appear during startup, preheating or a self-diagnosis test.
- The precise behaviour can vary by model, software version and the point at which -dC- is detected.
Common causes
- Samsung Range, wall oven or induction cooktop -dC- is associated with the door, lid or latch condition described in Samsung's guidance.
- The door, lid or partition may not be fully seated in the position expected by the appliance.
- Clothing, packaging, residue or another obstruction may be preventing the latch from engaging.
- The latch or position sensor may be misaligned or damaged.
- Internal wiring or the control circuit may not be receiving the correct closed-position signal.
- The display code alone cannot confirm which cause applies; diagnosis should begin with the least invasive documented checks.
Before you start troubleshooting
Use the display, rating label or product menu to confirm the exact model. Similar-looking codes can have different meanings across product generations and regions.
- Record the code and allow hot surfaces to cool.
- Check the door, controls and external power supply only as the manufacturer directs.
- Never remove the casing or work on high-voltage, gas or internal heating parts.
Troubleshooting steps
- Photograph or write down -dC-, the model number and what the cooking appliance was doing when the code appeared.
- Read the Samsung guidance linked in the source field and check that it applies to the exact model and region.
- Switch the product to a safe idle state and remove any visible obstruction around the seal or latch.
- Close the door or lid firmly without forcing it.
- Check that removable partitions or accessories are installed in the documented position.
- Restart the operation once and note whether the code appears immediately or later.
- If -dC- returns, stop repeating resets and arrange authorised diagnosis with the recorded details.
Can you fix this error code yourself?
The safest next step depends on the exact model and the cause behind the code. External checks may help, but a returning fault needs professional diagnosis.
A successful reset is not proof that the underlying issue is fixed. If -dC- reappears, note when it happens and give that information to the service engineer.
Reset instructions
After the appliance is cool, use one power reset only if Samsung's instructions permit it. Re-enter required clock or control settings afterwards. Do not keep resetting a temperature, wiring or electronic fault. A reset can clear the display without correcting the cause, so confirm normal operation afterwards and retain a record of -dC- for the engineer.
Applicable products and models
Range, wall oven or induction cooktopModel and region dependentWhen to contact a professional
Contact Samsung or an authorised service provider if -dC- returns after the documented external checks, appears with leakage, smoke, overheating, electrical tripping, unusual noise or loss of a safety-critical function. Professional diagnosis is also required whenever testing would involve internal wiring, refrigerant, gas, high-voltage, sealed-system or moving components. Provide the full code, model number, serial details, region and the stage of operation at which the fault occurs.
Frequently asked questions
What does Samsung Range, wall oven or induction cooktop -dC- mean?
The oven partition is missing, incorrectly installed or the partition switch is obstructed. Samsung uses -dC- to identify a door, lid or latch condition on the affected cooking appliance. The code is a diagnostic starting point rather than proof that one specific part has failed. Confirm the complete code, exact model number and region before using repair information or ordering components.
Can I fix Samsung Range, wall oven or induction cooktop -dC- myself?
Some external checks may be suitable for the user, but the result depends on the exact model and cause. Use the official manual and arrange service if the code returns.
Should I reset the product after code -dC-?
After the appliance is cool, use one power reset only if Samsung's instructions permit it. Re-enter required clock or control settings afterwards. Do not keep resetting a temperature, wiring or electronic fault. A reset can clear the display without correcting the cause, so confirm normal operation afterwards and retain a record of -dC- for the engineer.
When should I arrange a repair?
Contact Samsung or an authorised service provider if -dC- returns after the documented external checks, appears with leakage, smoke, overheating, electrical tripping, unusual noise or loss of a safety-critical function. Professional diagnosis is also required whenever testing would involve internal wiring, refrigerant, gas, high-voltage, sealed-system or moving components. Provide the full code, model number, serial details, region and the stage of operation at which the fault occurs.