tE error code
Temperature sensor error
What does Samsung Microwave oven tE mean?
Temperature sensor error. Samsung uses tE to identify a sensor or temperature-monitoring condition on the affected washing machine. The code is a diagnostic starting point rather than proof that one specific part has failed. Confirm the complete code, exact model number and region before using repair information or ordering components.
The code identifies the condition detected by the product; it does not always identify the failed component on its own. Confirm the full code and exact model before ordering parts or attempting a reset.
The Samsung Microwave oven tE error code indicates temperature sensor error. Samsung uses tE to identify a sensor or temperature-monitoring condition on the affected washing machine. The code is a diagnostic starting point rather than proof that one specific part has failed. Confirm the complete code, exact model number and region before using repair information or ordering components. This guide explains what the code means, the symptoms and likely causes, the checks that are safe to make, and when to stop and arrange an authorised repair.
Symptoms you may notice
- The washing machine displays tE and may interrupt its wash or rinse cycle.
- The cycle may pause before filling, washing, spinning or draining.
- The remaining-time display may stop changing while the code is active.
- Water level, drum movement or door operation may differ from normal.
- The precise behaviour can vary by model, software version and the point at which tE is detected.
Common causes
- Samsung Washing machine tE is associated with the sensor or temperature-monitoring condition described in Samsung's guidance.
- The relevant sensor may be reporting a value outside its expected range.
- A connector or wiring path may be open, shorted, loose or affected by moisture.
- Airflow, icing, heat or the surrounding operating conditions may be influencing the reading.
- The sensor or electronic control board may require calibrated testing.
- The display code alone cannot confirm which cause applies; diagnosis should begin with the least invasive documented checks.
Before you start troubleshooting
Use the display, rating label or product menu to confirm the exact model. Similar-looking codes can have different meanings across product generations and regions.
- Record the code and allow hot surfaces to cool.
- Check the door, controls and external power supply only as the manufacturer directs.
- Never remove the casing or work on high-voltage, gas or internal heating parts.
Troubleshooting steps
- Photograph or write down tE, the model number and what the washing machine was doing when the code appeared.
- Read the Samsung guidance linked in the source field and check that it applies to the exact model and region.
- Record the complete code and the operating conditions when it appeared.
- Allow the product to return to a normal ambient temperature if Samsung guidance permits.
- Check only accessible vents, filters and external obstructions associated with the affected area.
- Do not bridge, heat, cool or electrically test an internal sensor yourself.
- If tE returns, stop repeating resets and arrange authorised diagnosis with the recorded details.
Can you fix this error code yourself?
The safest next step depends on the exact model and the cause behind the code. External checks may help, but a returning fault needs professional diagnosis.
A successful reset is not proof that the underlying issue is fixed. If tE reappears, note when it happens and give that information to the service engineer.
Reset instructions
Cancel the cycle only if the controls respond normally. After completing the documented external checks, disconnect power for the period stated in the exact Samsung model manual, reconnect it and run one short test cycle. Do not repeatedly reset a returning code. A reset can clear the display without correcting the cause, so confirm normal operation afterwards and retain a record of tE for the engineer.
Applicable products and models
Microwave ovenModel and region dependent
Tumble dryerModel and region dependent
Washing machineModel dependentWhen to contact a professional
Contact Samsung or an authorised service provider if tE returns after the documented external checks, appears with leakage, smoke, overheating, electrical tripping, unusual noise or loss of a safety-critical function. Professional diagnosis is also required whenever testing would involve internal wiring, refrigerant, gas, high-voltage, sealed-system or moving components. Provide the full code, model number, serial details, region and the stage of operation at which the fault occurs.
Frequently asked questions
What does Samsung Microwave oven tE mean?
Temperature sensor error. Samsung uses tE to identify a sensor or temperature-monitoring condition on the affected washing machine. The code is a diagnostic starting point rather than proof that one specific part has failed. Confirm the complete code, exact model number and region before using repair information or ordering components.
Can I fix Samsung Microwave oven tE myself?
Some external checks may be suitable for the user, but the result depends on the exact model and cause. Use the official manual and arrange service if the code returns.
Should I reset the product after code tE?
Cancel the cycle only if the controls respond normally. After completing the documented external checks, disconnect power for the period stated in the exact Samsung model manual, reconnect it and run one short test cycle. Do not repeatedly reset a returning code. A reset can clear the display without correcting the cause, so confirm normal operation afterwards and retain a record of tE for the engineer.
When should I arrange a repair?
Contact Samsung or an authorised service provider if tE returns after the documented external checks, appears with leakage, smoke, overheating, electrical tripping, unusual noise or loss of a safety-critical function. Professional diagnosis is also required whenever testing would involve internal wiring, refrigerant, gas, high-voltage, sealed-system or moving components. Provide the full code, model number, serial details, region and the stage of operation at which the fault occurs.